Text Hover

Faster load ins, smoother rehearsals, safer stages - wire your facility to take full advantage of stage automation. A variety of hardwired receptacles reduces the manpower and time running cables for any automated effect. Skilled technicians can plug in a motion controller or control device and get moving. Set up time is reduced by as much as 30% - that amounts to reduced labor cost & more time putting on a show.

Permanently installed remote boxes distributed throughout the facility connect to a centrally located control rack and form the backbone of a nimble network capable of supporting your most complicated automation needs. The remote boxes provide connectivity for Stagehand drives, control devices (like the Spikemark Pendant or Consolette), and distributed emergency stop mushroom buttons.

Drive Connection

The Drive Connection lets you connect remotely deployed Stagehands to racked Showstopper components. No more long e-stop or Cat5 cable runs.

It incorporates an Ethernet and Showstopper connection in a standard 3 gang box. Easy for your electrical contractor to install and only requires low voltage connections.

Available as a surface mount or flush mount box depending on the installation needs. Each faceplate includes standard nomenclature as well as customized ID numbers to maintain clean and organized cable terminations.

Control Connection

The Control Connection allows for any control device to be connected at any convenient position. Easily drop in a new Spikemark computer, Stage Manager, Consolette, or Pendant without re-running cables.

Each box includes one Showstopper 3 Accessory output and two Ethernet receptacles, which makes connecting control devices or e-stop accessories a cinch.

It even supports connecting a Showstopper 3 Hub to support additional production automation.

It is available as surface mount as well as flush mount box depending on the installation needs and includes standard nomenclature as as well customized ID numbers.

Showstopper Remote

Moving is only half the equation… Stopping is just as important.

Showstopper Remotes can be installed throughout a facility so an e-stop is always nearby. They are hard wired into the Showstopper system through a flush mount or surface mount box and often are spreadout on the grid, stage level, trap room, and key front of house positions.

Each remote includes an illuminated E-Stop button, system status indicator, tool-less field terminations and customizable nomenclature.

Text Hover

Your electrical contractor can pull wiring through conduit to connects remote boxes to a control rack. Racked equipment can include an any of the below equipment along with a network switch, UPS power supply and the Showstopper 3 Base.

Showstopper Base

Where it all begins. This rack-mountable device can power the emergency-stop contactors of up to 10 Stagehands and is the device hub for Showstopper accessories.

Find Out More Here

Showstopper E-Stop Hub

As your inventory of automated effects grows, the backbone of your system can grow with it. Connect an additional 10 Stagehands to the emergency stop system. Add multiple Hubs to infinitely expand your system.

Installation is simple. Connect the Hub via the Base’s accessory port and you’re done.

Showstopper Hub also includes an additional accessory port so you never run out of connectors for additional control or e-stop equipment.

Showstopper Accessory Patch Panel

The Accessory Patch panel incorporates tool-less facility wiring terminations on the back along with tried and true panel mount Harting 3A panel mount connections.

The toolless terminations make short work of wiring in the field, and the familiar connectors keep connections simple for the user.

Showstopper E-Stop Patch Panel

The E-stop Patch panel incorporates tool-less facility wiring terminations on the back along with tried and true panel mount 5 pin XLR Showstopper connections on the front.

Integrating these brings harmony to the installer and end-user.

Showstopper Accessory Hub

The Accessory Hub lets you add even more accessories directly at the rack.

Whether you need to directly connect a Pendant or additional Control Connection boxes are installed in your venue, the Accessory Hub allows for quick expansion and additions.

Need help designing your facility layout?

Connect with an automation expert now.

Get Started

Sample Layout

Text Hover

Get Help With Permanant Install Components

Our technical service team can work with you to design the perfect system.

Get a Quote

Resources

Typical System Riser

White Paper

Hub Manual

Base Manual